Votronic Automatic Charger VAC 1250 F 3A

Product description

Charging programmes no. 5, 6, 7, 8 and 9 (start, gel, AGM, acid) adjustable to battery type
Outstanding charging technology
Fully automatic continuous operation for constant operational readiness of the batteries
The charging voltages are free of peaks and regulated in such a way that overcharging is ruled out
Trouble-free operation and co-supply of the devices connected to the vehicle electrical system
Built-in charging current distributor with 2 main charging outputs, both with maximum current and power capacity
Charging current distributor output "2" can optionally be switched to a separate charging programme for the starter battery
Starter battery is also charged with full charging current if required (short vehicle service life)
Signal output (MA) +86 for engine start inhibit with vehicle mains connection
Visual and acoustic warning in the event of battery and operating errors
Precise battery temperature compensation, temperature sensors included in the scope of delivery
Automatic battery regeneration during long downtimes (twice a week)
Compensation of voltage losses on the charging cables for exact compliance with the charging voltages
Disconnection of the batteries in the event of mains failure, overheating, incorrect behaviour (safety switch per charging output)
Power supply function enables consumers to continue operation and data retention, e.g. when changing batteries
Manual charging start when battery is deeply discharged in accordance with DIN 14679
Variable installation position
Electronics protected against moisture
Intelligent microprocessor control takes into account the simultaneous co-supply of consumers on the battery
Mains/charging power can be reduced if the mains supply is weak or limited (power limit function)

Optional accessories:

Remote control S (Art. 2075)
Remote operating display IP67 (Art. 2081)
Charger State Monitor IP67 (Art. 2082)

Technical data

Charging power in [V]/[A]	12 / 50
Nominal voltage (AC) in [V]	230
Operating voltage range (AC) in [V]	190 - 265 (full charging capacity)
Power consumption (AC) in max. [W]	840
Sinusoidal power factor correction (CosPhi = 1)	Yes
Nominal battery voltage (DC) in [V]	12
Battery capacity in [Ah]	85 - 250 (500 ¹)
Charging current in [A]	50
Auxiliary charging output "S" in [A]	-
Charging characteristic	IU1oU2
Voltage limitation for all charging types/programmes [V]	15
Voltage ripple in [mV] rms	< 40
Number of charging outputs	2 + MA
Device installation position	any
Temperature range [°C]	-20 to +45
Degree/class of protection	I / IP 21
Dimensions (WxHxD) in [mm] - Dimensions incl. mounting flanges, without connections	305 x 71 x 160
Weight in [g]	2450
Standards (CE)	EN 60335-2-29
Ambient conditions, humidity: max. 95% room humidity, non-condensing
Scope of delivery: Mains cable, 2 temperature sensors, operating instructions

¹ when vehicles are not in use for >24 hours, in accordance with DIN 14679

Safety instructions and warnings

Safety instructions for Votronic Automatic Charger VAC 1250 F 3A:

1 Always switch off the power supply before installing or servicing the charger.

2. ensure that the charger does not come into contact with water or other liquids.

3. use the charger only for its intended purpose in accordance with the manufacturer's instructions.

4. do not overcharge the battery. Observe the specified maximum charging capacity.

5. keep the charger away from children and do not leave it unattended.

6. do not use the charger if it is damaged or shows signs of malfunction.

7. observe all applicable electrical safety guidelines and regulations.

8. only use spare parts or accessories recommended by the manufacturer.

9. switch off the charger before cleaning or working on it.

10. observe the manufacturer's specific safety instructions for the intended use of the charger.

Manufacturer contact information

Manufacturer Contact

VOTRONIC Elektronik-Systeme GmbH
Johann-Friedrich-Diehm-Str. 2
36341 Lauterbach

https://www.votronic.de/kontakt/