- Product description
- Charging programmes no. 1, 2, 3 and 5 (gel, AGM, acid, start) adjustable to battery type
- Outstanding charging technology
- The charging voltages are free of peaks and regulated to prevent overcharging
- 1 main charging output and 1 additional auxiliary charging output "S" for supporting and trickle charging a starter battery (max. 2 A)
- Starter battery is also charged with full charging current if required (short vehicle service life)
- Fully automatic continuous operation for constant operational readiness of the batteries
- Precise battery temperature compensation, temperature sensor included in the scope of delivery
- Equalisation function (IUIU charging characteristic can be activated manually for cell equalisation charging)
- Intelligent microprocessor control takes into account the simultaneous co-supply of consumers on the battery
- Automatic battery regeneration during long downtimes (twice a week)
- Equalisation of voltage losses on the charging cables for exact compliance with the charging voltages
- Disconnection of the batteries in the event of mains failure, overheating, incorrect behaviour (safety switch per charging output)
- Silent run function can be set (night setback)
- Mains adapter function enables consumers to continue operation and data retention, e.g. when changing batteries
- Electronics protected against moisture
- Variable installation position
- Battery capacity adjustable in 4 stages (16 charging programmes in total)
- Input for sensor (sense) cables, can be used with extra-long charging cables
- Separate signalling output +86 for engine start inhibit with vehicle mains connection
- Voltage equalisation for external diode charging current distributor selectable (+ 0.63V)
- Mains/charging power can be reduced in the event of low-power or restricted mains supply, e.g. weakly fused shore power supply, generator operation, etc. (power limit function)
Optional accessories:
- Remote control S (Art. 2075)
- Remote operating display IP67 (Art. 2081)
- Charger State Monitor IP67 (Art. 2082)
Technical data
| Charging power in [V]/[A] | 12 / 60 |
| Nominal voltage (AC) in [V] | 110 - 230 |
| Operating voltage range (AC) in [V] | 115 - 265 (full charging capacity) |
| Power consumption (AC) in max. [W] | 1020 |
| Sinusoidal power factor correction (CosPhi = 1) | Yes |
| Nominal battery voltage (DC) in [V] | 12 |
| Battery capacity in [Ah] | 120 - 660 |
| Charging current in [A] | 60 |
| Auxiliary charging output "S" in [A] | 2 |
| Charging characteristic | IU1oU2 |
| Voltage limitation for all charging types/programmes [V] | 15 |
| Voltage ripple in [mV] rms | < 50 |
| Number of charging outputs | 2 + S |
| Device installation position | any |
| Temperature range [°C] | -20 to +45 |
| Degree/class of protection | I / IP 21 |
| Dimensions (WxHxD) in [mm] - Dimensions incl. mounting flanges, without connections | 305 x 90 x 265 |
| Weight in [g] | 3.900 |
| Standards (CE) | EN 60335-2-29 |
| Ambient conditions, humidity: max. 95% room humidity, non-condensing | |
| Scope of delivery: Mains cable, 2 temperature sensors, operating instructions |
Safety instructions and warnings
Safety instructions for Votronic Automatic Charger VAC 1260 M 3A / 110 V AC
1. use the device only in closed rooms and keep it away from moisture
2. ensure that the device is properly connected and earthed.
3. do not touch the appliance while it is in operation and wear suitable protective gloves if necessary.
4. keep the appliance away from children and pets.
5. do not use the appliance near flammable materials.
6. switch off the appliance before cleaning or servicing.
7. keep the appliance out of reach of water.
8. use only spare parts recommended by the manufacturer.
Manufacturer contact information
Manufacturer Contact
VOTRONIC Elektronik-Systeme GmbH
Johann-Friedrich-Diehm-Str. 2
36341 Lauterbach
https://www.votronic.de/kontakt/