- Product description
- Technical details
- Charging programmes no. 1, 2, 3 and 5 (gel, AGM, acid, start) adjustable to battery type
- The charging voltage is free of peaks and regulated in such a way that overcharging of the batteries is excluded.
- Fully automatic continuous operation: The charger can be permanently connected to the battery and keeps it fully charged. In case of mains failure, the batteries are not discharged (disconnected by safety switch).
- Lead-acid battery regeneration twice a week during long periods of inactivity to prevent harmful acid stratification.
- Parallel and buffer operation: In case of simultaneous consumption, the battery is further charged or kept full. The charger automatically calculates and monitors the adjustment of the charging times.
- Monitoring-free charging: Multiple protection against overload, overheating, overvoltage, short-circuit, reverse polarity, faulty operation and battery back-discharge by electronic cut-off up to complete disconnection of charger and battery by built-in safety switches.
- Connection for battery temperature sensor (temperature sensor 825 included in delivery): For lead batteries (acid, gel, AGM), the charging voltage is automatically adapted to the battery temperature, resulting in better full charging of the weaker battery in cold weather, and in summer temperatures, unnecessary battery gassing and thus battery strain is avoided.
- Silent Run function: noise-optimised operation at the touch of a button (night operation).
- Power supply function: Enables the supply of consumers without battery (e.g. when changing the battery).
- Charging cable compensation: Voltage losses on the charging cables are automatically compensated.
- Built-in on-board power supply filter: Problem-free parallel operation with solar systems, wind and petrol generators, dynamos etc. on one battery.
- Electronics moisture-protected
- Charging aid for deeply discharged lead batteries: Gentle pre-charging of the (lead-acid, -gel, -AGM) battery up to 8 V, then powerful support of the battery for consumers that may still be switched on.
- Built-in charging current distributor with 2 main charging outputs, both with max. current and power capacity.
- In case of mixed operation with 1 supply and 1 starter battery, a separate starter charging programme can be set on the built-in charging current distributor
- Starter battery is also charged with full charging current if required (short vehicle standing time)
- Separate auxiliary charging output "S" for backup and maintenance charging of another starter battery or as signal output +86 for engine start inhibition when the vehicle is connected to the mains.
- Equalisation function (IUIU charging characteristic can be activated manually for cell equalisation charging)
- Disconnection of batteries in case of mains failure, overheating, malfunction (safety switch per charge output)
- Variable installation position
Optional accessories:
- Remote control S (art. 2075)
- Remote operating display IP67 (art. 2081)
- Charger State Monitor IP67 (art. 2082)
Charging power in [V]/[A] | 24 / 16 |
Rated voltage (AC) in [V] | 230 |
Operating voltage range (AC) in [V] | 190 - 265 (full charging capacity) |
Power consumption (AC) in max. [W] | 520 |
Sinusoidal power factor correction (CosPhi = 1) | yes |
Nominal battery voltage (DC) in [V] | 24 |
Battery capacity in [Ah] | 40 - 200 |
Charging current in [A] | 16 |
Auxiliary charging output "S" in [A] | 2 |
Charging characteristic | IU1oU2 |
Voltage limitation for all charging types/programmes [V] | 30 |
Voltage ripple in [mV] rms | < 50 |
Number of charging outputs | 2 + S |
Device installation position | any |
Temperature range [°C] | -20 to +45 |
Degree/class of protection | I / IP 21 |
Dimensions (WxHxD) in [mm] - Dimensions incl. mounting flanges, without connections | 210 x 71 x 160 |
Weight in [g] | 1450 |
Standards (CE) | EN 60335-2-29 |
Ambient conditions, humidity: max. 95% room humidity, non-condensing | |
Scope of delivery: Mains cable, 1 temperature sensor, operating instructions |