- Product description
- 2 completely separate and independent charging units in one device
- Charging programmes no. 1, 2, 3 and 5 (gel, AGM, acid, start) can be set for each charging unit depending on the battery type
- Battery capacity can be set 4 times per charging section (16 charging programmes in total)
- Outstanding charging technology
- Signalling output (MA) +86 for engine start inhibit when connected to the vehicle power supply
- Automatic battery regeneration for long downtimes (twice a week)
- Compensation of voltage losses on the charging cables for exact compliance with the charging voltages
- Disconnection of the batteries in the event of mains failure, overheating, incorrect behaviour (safety switch per charging output)
- Electronics protected against moisture
- The charging voltages are free of peaks and regulated to prevent overcharging
- Fully automatic continuous operation for constant operational readiness of the batteries
- Precise battery temperature compensation, temperature sensor included in the scope of delivery
- Intelligent microprocessor control takes into account the simultaneous co-supply of consumers on the battery
- Built-in 200A battery bridging function for emergency engine start
- Emergency engine start can also be operated remotely with a simple push-button switch, e.g. from the dashboard
Optional accessories:
- Remote display S (Art. 2078)
- Remote operating display IP67 (Art. 2081)
- Charger State Monitor IP67 (Art. 2082)
Technical data
| Charging power in [V]/[A] | 12 / 15 / 30 |
| Nominal voltage (AC) in [V] | 230 |
| Operating voltage range (AC) in [V] | 190 - 265 (full charging capacity) |
| Power consumption (AC) in max. [W] | 720 |
| Sinusoidal power factor correction (CosPhi = 1) | Yes |
| Nominal battery voltage (DC) in [V] | 12 |
| Battery capacity in [Ah] | 36 - 170 / 75 - 350 |
| Charging current in [A] | 15 / 30 |
| Auxiliary charging output "S" in [A] | - |
| Charging characteristic | IU1oU2 |
| Voltage limitation for all charging types/programmes [V] | 15 |
| Voltage ripple in [mV] rms | < 50 |
| Number of charging outputs | 2 |
| Device installation position | any |
| Temperature range [°C] | -20 to +45 |
| Degree/class of protection | I / IP 21 |
| Dimensions (WxHxD) in [mm] - Dimensions incl. mounting flanges, without connections | 305 x 90 x 265 |
| Weight in [g] | 3700 |
| Standards (CE) | EN 60335-2-29 |
| Ambient conditions, humidity: max. 95% room humidity, non-condensing | |
| Scope of delivery: Mains cable, 2 temperature sensors, operating instructions |
Safety instructions and warnings
Safety instructions for Votronic Automatic Charger VAC 1215/30 Duo:
1. please read the manufacturer's instructions carefully before commissioning.
2. only use the product in accordance with the manufacturer's specifications and instructions.
3. ensure that the electrical installation complies with the applicable safety standards.
4. ensure that the product is protected from moisture and heat.
5. do not use the product near flammable materials.
6. switch off the appliance before cleaning or carrying out maintenance work.
7. use only accessories or spare parts recommended by the manufacturer.
8. keep the product away from children and do not leave it unattended.
9. do not overload the product and do not subject it to excessive loads.
10. if problems or malfunctions occur, contact the manufacturer or authorised customer service.
11. observe the applicable regulations and guidelines for the safe operation of the device.
12 In the event of a power failure or malfunction, disconnect the product from the power supply.
13. avoid opening the device improperly or carrying out repairs yourself.
14. dispose of the product properly in accordance with local rules and regulations.
Manufacturer Contact information
Manufacturer
VOTRONIC Elektronik-Systeme GmbH
Johann-Friedrich-Diehm-Str. 2
36341 Lauterbach
https://www.votronic.de/kontakt/